Installing a Portable Air Conditioner in a Crank Out Window
A practical, step-by-step guide to venting and sealing a portable AC through a casement or crank out window — without losing cooling efficiency or damaging your window frame.
Explore Venting MethodsWhat This Guide Covers
Why Crank Out Windows Are Different
Crank out windows — also called casement windows — open outward on a hinge, typically controlled by a hand crank or lever. This design is excellent for ventilation and energy efficiency, but it creates a unique challenge for portable air conditioner installation. Standard portable AC window kits are built for vertical or horizontal sliding windows, where a flat panel can rest in the track and the window sash slides against it.
With a crank out window, there is no sliding sash and no flat track to hold a standard kit. The window swings outward, leaving an angled opening that varies in width depending on how far the crank is turned. This means the venting solution must be custom-fitted to the window opening and must allow the window to close against a rigid surface.
Before deciding on a method, check whether your window opens inward or outward. Most casement windows open outward, but some European-style windows tilt inward. An outward-opening window is easier to work with because the panel sits inside the frame and the window presses against it. Inward-opening windows require a different approach and may need a professional adapter.
Venting Methods Compared
There are three practical approaches to venting a portable AC through a crank out window. Each has trade-offs in terms of installation effort, sealing quality, and how much the window can remain open.
| Method | Best For | Sealing Quality | Installation Effort | Reusability |
|---|---|---|---|---|
| Custom acrylic/plexiglass panel | Permanent or seasonal setups in bedrooms, living rooms, home offices | High — rigid panel with weatherstripping | Moderate — requires measuring and cutting or ordering | Reusable each season |
| Fabric window seal with zipper | Renters and temporary setups | Moderate — depends on fabric fit and taping | Low — tapes around the opening | Reusable with new tape |
| Insulated foam board panel | Small openings and tight spaces | Moderate to high when sealed properly | Low to moderate — cut foam board to size | Reusable if handled carefully |
Custom Acrylic or Plexiglass Panel
This is the most durable and best-sealing option. A clear acrylic panel is cut to the inside dimensions of the window frame, with a circular hole sized to the exhaust hose diameter. The panel sits in the frame, and the crank out window closes against it. Clear acrylic lets light through, which is a significant advantage in small rooms. Many hardware stores will cut acrylic to your measurements.
For a more finished look, you can add a foam gasket around the panel edge and a hose collar or flange around the hole. This method works well for both single-hose and dual-hose portable units, though dual-hose units require two holes or a wider panel.
Fabric Window Seal with Zipper
A fabric seal is a large sheet of durable fabric with a zippered opening for the hose. It attaches to the window frame with adhesive tape or hook-and-loop strips and wraps around the exhaust hose. This method is popular with renters because it requires no cutting and leaves no permanent marks. However, the seal is only as good as the tape adhesion, and the fabric can flap in wind or degrade over time.
Fabric seals work best when the window can remain slightly open and the fabric can be taped tightly around the hose. If the crank out window does not close flush against the fabric, hot air can leak back into the room, reducing cooling performance.
Insulated Foam Board Panel
Rigid foam insulation board is a practical option for small openings or temporary setups. It can be cut with a utility knife, is relatively sturdy, and provides decent insulation. A hole is cut for the exhaust hose, and the board is fitted into the window frame with weatherstripping around the edges. Foam board is less durable than acrylic and can crumble if mishandled, but it works well as a seasonal solution.
Materials and Tools You Need
Gather these materials before starting. Most are available at hardware stores, and some portable AC units include a basic window kit you can adapt.
Materials
- Acrylic or plexiglass sheet — cut to the window opening dimensions, typically 1/8 to 1/4 inch thick
- Foam weatherstripping — adhesive-backed, for sealing the panel perimeter
- Weather seal tape or foil tape — for sealing around the hose and panel edges
- Exhaust hose collar or flange — optional, for a cleaner hose connection
- Foam insulation strip — for filling larger gaps
- Removable caulk or rope caulk — for temporary gap sealing
- Hook-and-loop strips or adhesive tape — if using a fabric seal
Tools
- Tape measure and pencil
- Utility knife or jigsaw (for cutting acrylic or foam board)
- Drill with hole saw (for cutting the hose hole in acrylic)
- Sanding block or fine sandpaper (to smooth cut edges)
- Scissors (for weatherstripping and tape)
- Gloves and safety glasses
Step-by-Step Installation Process
Follow these steps for a custom acrylic panel installation, which is the most reliable method for a crank out window.
- Measure the window opening. Open the crank out window fully. Measure the height and width of the inside frame opening. Measure at the top, middle, and bottom for width, and at the left, center, and right for height. Use the smallest measurements to ensure the panel fits. Note the depth of the frame so the panel sits flush.
- Determine the hose hole position. Hold the exhaust hose against the window opening to decide where the hole should go. The hole should be low enough that the hose can run to the portable unit without sharp bends, and positioned so the window crank mechanism does not interfere. Mark the center point.
- Cut the acrylic panel. Order or cut the acrylic to your measurements. Cut the hose hole using a hole saw sized to the hose diameter (typically 5 to 6 inches for portable AC exhaust hoses). Sand the edges smooth.
- Apply weatherstripping to the panel edge. Run adhesive foam weatherstripping around the entire perimeter of the panel on the side that faces the window. This creates a compression seal when the window closes against the panel.
- Install the hose collar. If using a collar or flange, screw or glue it around the hose hole. This holds the hose securely and prevents it from slipping out.
- Position the panel in the window frame. Open the crank out window and place the panel into the frame opening. The panel should sit against the inside stop or frame edge. If the frame has a lip, the panel can rest against it; otherwise, use small L-brackets or removable adhesive strips to hold it in place.
- Close the window against the panel. Crank the window closed until it presses firmly against the weatherstripping. The window should lock or latch if possible. If the crank mechanism prevents full closure, adjust the panel position or use a thinner panel.
- Connect the exhaust hose. Attach the hose to the portable AC unit and route it through the hole in the panel. Secure the hose to the collar or use foil tape around the connection.
- Seal remaining gaps. Inspect the perimeter of the panel and the hose connection. Fill any gaps with foam insulation, weather seal tape, or removable caulk. Pay special attention to the corners and the area around the crank mechanism.
- Test the installation. Turn on the portable AC and check for air leaks around the panel. Hold a tissue or your hand near the edges; if it flutters or you feel warm air escaping, add more sealing. Also confirm that the window is secure and the panel does not wobble.
Sealing and Insulation Techniques
A portable AC only cools effectively if the hot exhaust air goes outside and does not leak back in. Sealing is the most important part of the installation, especially with a crank out window where the opening is irregular.
Perimeter Sealing
Foam weatherstripping is the first line of defense. Apply it to the panel edge that contacts the window frame and the window sash. Closed-cell foam is more durable and resistant to moisture than open-cell foam. For gaps wider than a quarter inch, use a foam backer rod or strip insulation before applying tape.
Hose Connection Sealing
The hose-to-panel connection is a common leak point. If your panel has a collar, twist the hose firmly into the collar and wrap the joint with foil tape. If there is no collar, use a hose clamp or several wraps of weather seal tape. Avoid using duct tape for long-term installations because it leaves residue and degrades in heat.
Window Crank Area
The crank mechanism often leaves a small gap at the bottom or side of the window. Fill this with removable caulk, rope caulk, or a small piece of foam insulation. Check that the crank handle does not prevent the window from closing fully against the panel; if it does, you may need to remove the handle temporarily or choose a different panel position.
Insulating the Panel
Clear acrylic transmits heat, so on very hot days the panel itself can warm up. If you notice heat gain, apply a reflective window film to the outdoor side of the panel or use a white foam board instead of clear acrylic. Insulating the exhaust hose with a hose cover also reduces heat radiating back into the room.
Safety and Load Considerations
Crank out windows are not designed to support heavy objects, and the glass and hinge mechanism can be damaged by excessive force. Keep these safety points in mind:
- Use lightweight panels. Acrylic and foam board are much lighter than glass. Avoid thick glass panels, which can strain the window hinges.
- Secure the panel against falling. If the panel is not held by the window frame, use removable adhesive strips or small brackets. Never rely on friction alone, especially in homes with children or pets.
- Do not block the window's emergency exit function. If the crank out window is a required egress point, make sure the panel can be removed quickly in an emergency.
- Check the window lock. The window should still lock or latch with the panel in place. If it does not, use a secondary security device such as a window bar or cable lock.
- Keep the hose free of kinks. A kinked hose restricts airflow and can cause the unit to overheat. Route the hose with gentle curves and support it if necessary.
- Use a dedicated circuit. Portable AC units draw significant current. Plug the unit directly into a wall outlet, not an extension cord, and confirm the circuit can handle the load.
If your window is large, old, or difficult to seal, consider a professional assessment. An HVAC technician can advise on whether a different cooling solution, such as a ductless mini-split, is a better fit for your space. You can explore options for professional installation through local service providers.
Maximizing Cooling Efficiency
Once the portable AC is installed and vented, a few adjustments can improve performance and comfort:
- Match BTU to room size. An undersized unit runs constantly without cooling effectively; an oversized unit cycles too quickly and leaves the room humid. Use a BTU guide for your room dimensions.
- Use a dual-hose unit when possible. Dual-hose portable ACs draw intake air from outside rather than from the conditioned room, which maintains better pressure balance and cooling efficiency.
- Shade the window. Crank out windows often face direct sun. Use an exterior shade, awning, or reflective film to reduce solar heat gain.
- Insulate the exhaust hose. A hose cover or wrap reduces heat transfer from the hot exhaust back into the room.
- Keep the unit level and clear of obstructions. Maintain at least 12 to 18 inches of clearance around the unit's intake and outlet. Clean the filter regularly.
- Seal the room. Close doors to uncooled spaces, seal gaps under doors, and avoid running exhaust fans that pull cooled air out of the room.
For rooms without suitable windows, alternative solutions such as through-the-wall units or ductless systems may be more practical. If you are unsure which approach fits your home, compare installation methods and consult a qualified technician.
Frequently Asked Questions
Can you install a portable air conditioner in a crank out window?
Yes. A crank out window can accommodate a portable air conditioner with the right venting setup. The most reliable method is a custom acrylic or plexiglass panel with a hole for the exhaust hose, sealed with weatherstripping and closed against the window.
What is the best way to vent a portable AC through a casement window?
A rigid acrylic panel is the best method. It provides a flat, sealable surface for the hose and allows the window to close tightly against it. Fabric seals and foam board are alternatives but generally offer less durable sealing.
Do I need a special window kit for a crank out window?
Most portable AC units include a sliding window kit that does not fit crank out windows. You will likely need a casement window adapter panel, which you can buy from some manufacturers or have custom-cut from acrylic at a hardware store.
How do I seal the gap around the exhaust hose in a crank out window?
Use foam weatherstripping around the panel perimeter and foil tape or weather seal tape around the hose connection. Fill any remaining gaps with foam insulation or removable caulk. Check for leaks with a tissue test while the unit is running.
Will a portable AC work in a small room with a crank out window?
Yes, provided the unit is correctly sized for the room and the window is properly sealed. Crank out windows are common in small bedrooms and apartments, and a well-sealed acrylic panel makes portable AC operation effective.
Can I leave the portable AC installed year-round?
It is not recommended to leave the panel and hose installed permanently, especially in cold weather. Remove the panel at the end of the cooling season to allow the window to close normally and maintain energy efficiency.
Best Portable Air Conditioners for Crank Out Window Setups
⚠️ AFFILIATE DISCLOSURE: This website contains affiliate links. As an Amazon Associate, we earn from qualifying purchases. If you make a purchase through these links, we may receive a small commission at no additional cost to you. Read our full affiliate policy.
HOOMEE 118”(300CM) Universal Window Seal for Mobile Air Conditioner and Tumble Dryer – Window Kit Works with Portable AC, Easy to Install - Air Exchange Guards with Zip and Adhesive Fastener
Check price on Amazon
VOSE-FLO AC Window Seal Kit 157" for Casement Crank Out Windows, No-Drill | Portable AC Window Vent Kit, Adjustable, for Crank Casement, Push-Out Casement & Crank Skylight Windows, Waterproof
Check price on Amazon
HOOMEE 157”(400CM) Universal Window Seal for Mobile Air Conditioner and Tumble Dryer – Window Kit Works with Portable AC, Easy to Install - Air Exchange Guards with Zip and Adhesive Fastener
Check price on Amazon
SPONDWILD 157"/400CM Portable AC Window Seal Kit for Casement Windows | No-Drill Window Vent Kit, Fit 5" and 6" Single Hose Portable Air Conditioners, Waterproof Window Seal Kit, Easy Install
Check price on Amazon
HOOMEE 197”(500CM) Universal Window Seal for Mobile Air Conditioner and Tumble Dryer – Window Kit Works with Portable AC, Easy to Install - Air Exchange Guards with Zip and Adhesive Fastener
Check price on Amazon
Gruntbear Portable Air Conditioner Window Seal Kit for Casement 300CM/118” | Casement Window Ac Vent Kit for Mobile Air Conditioner and Tumble Dryer,Ac Window Seal Kit with Zip and Adhesive Fastener
Check price on AmazonDisclaimer
Some of the content on this site uses AI assistance. Information is provided for educational purposes only. We are not responsible for any losses resulting from the use of this information. By using this site, you waive any right to bring legal claims against us arising from your use of the information provided. If you do not agree, please do not use this site. Read the full disclaimer.